Different Types of Fridge Appliances

To meet the needs of various customers, manufacturers have developed various kinds of fridge appliances. To get the right appliance, you’ll need to be familiar with the features of each variant. Some are designed for energy efficiency while others to save space.

Bottom Freezers

While top freezers are still widespread Whirlpool Appliance Repair Los Angeles, the bottom freezer versions are gaining wide acceptance. The main selling point of these appliances is their energy efficiency. There are several styles, from the standard single door to twin French doors.

The typical French door freezer has narrow shelves. If you need more space, there are bottom freezers that provide space for larger trays. These can be kept at the bottom freezer.

Side by Side Fridge Appliances

These are vertically constructed refrigerators with French doors. The freezer is positioned on one side and the fridge on the other. The freezer and the fridge have separate doors.

These appliances are ideal for those with limited space because the doors are half the size of average swing door fridges. Some models are small enough they can be positioned next to kitchen islands or tables without getting in the way.

This variant is noted for being roughly the same size as single door refrigerators. The vertical setup means there are smaller but numerous shelves for each section. The fridge part typically has a couple of crisper drawers. The fridge section is usually larger than the freezer. Some of these fridge appliances are equipped with ice makers, pull out drawers and water dispensers.

Integrated Fridge / Freezers

These integrated units are also recommended for those with limited space. The freezer section is used to store meat, chicken, ice cream and other food that need to be frozen. The fridge portion is for storing and cooling assorted food items. Due to their efficiency and compactness, these appliances are often found in apartments and homes. These appliances are even used in finished basements as they don’t take up a lot of room.

Top Freezers

Also known as top-mount models, these units have the freezer at the top section. Along with the side by side, these fridge appliances are among the most widely used. The freezer is usually smaller compared with those of a side by side. However, top-mount models are less expensive.

Before You Buy

There are two major factors that come into play: the amount of food you need to store and available room. Before making a purchase, note the unit’s size; will it be enough to fit your current needs? If your current fridge is too small, try to calculate how much bigger the new fridge has to be.

Make Your Old Refrigerator Save You Money

Energy conservation and saving money are both things we see lately in appliance ads as it seems everyone has been encouraged to kick their old refrigerator to the curb and buy the latest and greatest thing, all with the promise of saving money and keeping the polar bears cold. But what if you don’t want to upgrade and are perfectly content with the appliances you already have? Well I for one am not going to tell you to throw out working appliances in the quest to save a few dollars but I can offer up some suggestions to help your old refrigerator use a little less energy, and save you some money doing it.

The typical home refrigerator is often referred to as the greatest energy hog in the kitchen (my guess is that kitchen doesn’t have an oven, but I digress) and considering it is literally running 50% of the time, this is a logical place to save some money. The reason for these long run times has to do with cooling demands and that is where we can take some steps to increase efficiency and start saving that cash. When was the last time you vacuumed the coils either behind or below your refrigerator? Not sure Refrigerator Repair Los Angeles?

Well you’re not alone, but failure to keep this area clean can greatly impact the refrigerators ability to keep things cool. You see if these coils become blocked due to dirt, dust, animal fur, coupons, cat toys etc., the airflow over these coils cannot draw heat away resulting in the refrigerator running longer than it should. Just like a car radiator that becomes blocked, it becomes harder to move the heat along and keep things cool. The best thing to do here is get out your trusty vacuum cleaner and clear off them coils along with any vents or grills that may protect them to allow for better airflow. You may also need to pull the refrigerator from the wall, unplug the power cord and remove the lower cover to really get in there and clean well. Brushes made just for this purpose can be found at most appliance retail or service locations if you really want to make things squeaky clean.

And while you are at it, this might be a good time to make sure the unit is positioned properly so it has adequate space around the cabinet to allow the air can flow. Your use and care manual has a very important page covering this often missed detail. A refrigerator that has poor airflow due to being pushed to close to a wall or inadequate spacing in a cabinet is just like running your car with half the radiator blocked. The better the airflow outside, the easier it will be to keep things cool inside. Follow the guidelines provided by the manufacturer for best results.

Another simple thing to do is ensure your refrigerator is loaded properly (yes this does make a difference) since items blocking airflow either entering or leaving the refrigerator can result in longer run times for the compressor. A refrigerator packed tightly can result in significant temperature changes from top to bottom and depending on the location of the temperature sensor this may keep things running longer than normal. Look around the cabinet for where the cold air enters and possibly exits and keep these areas clear. Again the use and care guide will point these areas out in detail.

How to Repair Whirlpool Washer Parts – Coupler

The Whirlpool washer coupler takes the place of the belt that is used on the older style washers. If your washer does not agitate or spin, there is a good chance the coupler is broke. The best way to change the coupler is to remove the cabinet. This is easier then it sounds. The first thing you need to do (after disconnecting the power) is to loosen the control panel. There are four different designs. The most common control panel is held in place to the cabinet with two screws at the base of the panel, on the right and left edge. The next common style is there are two screws on the backside of the panel on the right and left side. The third design is there are trim pieces attached to the control panel on each end. These trim pieces will pop off with a simple tug at the top After you remove the trim, you will find two screws in the front corners. The newest design is that there are spring style clip under the end caps of the control panel. You can release these clips with a butter knife or scrapper. You need to push the tool under the end caps and raise the control panel Washer Repair Los Angeles.

Tools you will need are: 1/4″ or 5/16″ socket or nut driver, standard screw driver, small hammer, 1/2″ socket with extension, pliers.

After you have loosened the panel, all you do is lift it upward and let it rest over the back panel of the washer. Now we need to disconnect the lid switch harness and remove the cabinet from the frame. To do this, you need to locate a spring clip on the outer edge of the top of the cabinet. You can release these clips by using a screw driver or sharp tool. Once you get the clips released, grab the cabinet and pull it toward you. The cabinet should hinge at the bottom front. Now you can pull the cabinet away from the frame and set it off to the side. Now you will need to release the clips that hold the pump to the motor. Take the clips completely off the motor. Next you need to take the screws out of the clips that hold the motor to the transmission and remove the clips using a standard screw driver. After these clips are removed, the motor should just fall toward the floor. Next you will need to unplug the motor wire harness from the motor and set the motor off to the side. At this point, you should be able to see all three parts to the coupler. Remove all three parts from the transmission and motor with a standard screw driver and inspect them for any cracks or broken parts. If the coupler is not broke in any way, there will probably be a problem with the transmission.

Now you are ready to install the new coupler. First put one piece (white plastic piece) on the transmission shaft. This is where you need the 1/2″ socket and extension. Line up the coupler to the shaft of the transmission and tap it on the rest of the way with the 1/2″ socket. You will not need to use much force. Repeat this process when putting the coupler on the motor. The third part of the coupler actually connects the motor and transmission together. You need to line up the post on the coupler with the holes in the rubber piece. Once this is done, put the clips back on the motor and reinsert the screws. Now you can plug the harness to the motor and reinstall the clips that hold the pump to the motor.

You are almost there. The cabinet is next to be put back on the frame. Push the front on the cabinet under the front edge of the frame and then let the cabinet fall towars the back panel. The side panels of the cabinet should rest on the frame tightly. If the side are bowing out, one side at a time you need to push the rear edge of the panel inward and lock on the frame. Reinstall the spring clips at the top and plug in the lid switch. Roll the control panel back over the cabinet and reinstall the screws or clips.

After the control panel is locked down, plug the washer back in and try the spin cycle. After you are sure the spin cycle is working, try the wash cycle and be sure it is ok. Now you are ready to do the wash and be proud of what you have done in repairing your washer.

Good luck in your repair experience!!

What Should I Look for in an Appliance Repair Professional?

Malfunctioning appliances are frustrating and inconvenient. When your fridge breaks down, your food can spoil. When your washing machine and dryer stop washing and drying, you have to wash clothes by hand, or take time out of your day to go to the laundromat. When your stove burners won’t light, you can’t prepare healthy, delicious meals for your family.

Luckily, most appliance repair experts can diagnose and fix these issues kenmore appliance repair los angeles, regardless of what brand or model of appliance you have. But with the array of appliance repair companies out there, even in a small town, how can you choose the right technician? Think about what’s important to you. Do you need repairs immediately? Do you want the lowest price? Or do you simply want assurance that you’re getting the best possible repair service? All of these factors can help you select the appliance repair company that’s right for you.

Training and Experience

Perhaps you simply want the best possible appliance repair service. How can you know someone’s skill is superior in his field? Look online or ask for information about the technician’s training and experience. The longer a repairman has been in the industry, the greater the chance he’ll have seen your appliance’s issue before and will know exactly how to fix it. Similarly, if a technician has training or certification to work with your specific high-end brand or model, or affiliation with an appliance repair organization, you can probably trust him to have the knowledge and skill to do the job right.

Turnaround Time

Do you need refrigerator repair immediately because you’re hosting a large event at home tomorrow? Did you wake up to your washing machine leaking all over the laundry room floor, and it won’t stop? Sometimes your biggest repair consideration has to be how quickly a technician can come out to your property and resolve the issue. Some appliance repair companies offer same-day service. Others will come out in an emergency, no matter the time of day. You may have to call several companies before finding someone who can fit you in immediately, but they’re out there. Note, however, that if you need appliance repairs with a quick turnaround time, you may have to sacrifice some other criteria-speed might cost more, or might mean you can’t be choosy about qualifications.

Price

Are you working within a tight budget? You can certainly research appliance repair companies in your area and compare their prices, looking for the best deal. But as with same-day service, you may have to sacrifice a few other preferences in order to keep costs down. For instance, you might have to wait longer for an appointment, and go without your appliance for a week or more. Or you might have to work with a brand-new technician rather than someone with 20 years of experience. When you do find a washer/dryer, refrigerator, or oven repair professional who fits your budget, give the rest of his qualifications a scan. You don’t want to have to call for repairs again in a month because the person you hired at a cheap price did a shoddy job.